How do i fix my mansfield toilet

But before you proceed with disassembling, make sure you have shut the water off to the toilet. This part is crucial because failure to do so will result in things getting really wet, and this is the last thing you want to happen. To turn off the valve, turn it all the way to the right. After you have taken apart the flush valve float, you will see a red seal located at the bottom of the tank.

The purpose of the seal is to stop leaks from the tank into the bowl. So when this seal is damaged, it can be the reason why your toilet is running or leaking. Now, you will need to pull the seal off in order to replace the valve. The seal might be difficult to take off and you might need to really give it a good pull so it stretches out of its groove. While replacing the seal is not that difficult, you do need to make sure you put the seal back in its correct spot.

Take note that there are two grooves located at the bottom where the seal is. Keep in mind that it might take a few tries before you successfully get it in the right spot. This way, you can see if there is another groove located above where your seal is. If the seal is in the groove then it will slide along and then you can use the same accessible spot to get the seal in the right place.

When you finally get the seal replaced, your toilet should stop running. In case the problem is still present, you can try the third solution which is detailed below. For instance, the valve may have a small hole which is causing all the problems. When you take out the float valve, make sure to visually inspect it for any issues. This way, you immediately know that you need to replace your valve rather than go through any other trouble.

If you spot holes or any other issues, get a flush valve float replacement and do the steps outlined in the previous section. Doing so should fix your leaky or running toilet. Contact Us Usually, there are two reasons why a leak causes a Mansfield toilet to run: The water level is set too high.

The flush valve seal is damaged. Is the water above line? Is it overflowing and going down the overflow tube? Put new seal into space between top two grooves. Slide the tower back on, screw on the cap, slide the refill tube back in place, turn on the water again, and you're done! Now that you have the new seal on, all you have to do is put everything back together.

Slide the tower back on, screw on the cap, slide the refill tube back in place, and turn on the water again. You're done! Content is for informational or entertainment purposes only and does not substitute for personal counsel or professional advice in business, financial, legal, or technical matters. Question: The flapper in a toilet I took a look at seals too well. It makes pushing the lever down extremely difficult. How do I get it to loosen up a bit? There is no chain to shorten.

Answer: That's exactly what my article is about -- that problem of "sealing too well. In a Mansfield toilet, there's a rubber ring between the two plastic parts of the tower assembly. That's the part that can be replaced.

I don't know what kind of toilet you're referring to, so you'll have to look closely and see if there's some piece with a rubber part that is causing the problem.

Answer: It depends on the model of the toilet's flushing assembly. I only found one size rubber replacement ring that was designed for a Mansfield toilet. I believe it's called a Mansfield Flush Valve Seal. If you're finding more than one option, the easiest way to be sure that you have the right one is to remove the old one and take it with you to the store.

Answer: I haven't had that happen to me -- in that case, I'd suggest trying the following:. Take the flush valve seal off and then re-install it to make sure it's properly placed, or. Inspect the tower assembly to make sure it's not broken or otherwise damaged so it won't seal to the new flush valve seal.

Replace that if necessary. If neither of those procedures work, then it's probably time to call in a professional, because the problem may not be a simple matter of replacing the rubber flush valve seal. Question: I have done this repair several times over the years but this time after replacing the seal with a new one it is still EXTREMELY hard to raise the flush tower with the handle.

Also the tower sometimes stays up after emptying the tank. Any ideas? Answer: Hmm. That's a puzzler! I'm not a plumber, just a DIY person, so my advice is: 1 Check to see if anything's rusted or broken around the handle or the connection with the flush tower, and if you don't see any easily fixable problems in those areas, then 2 call a licensed plumber. We should all be capable of fixing simple repairs, but when the problem isn't simple, it's time to call in the experts!

Question: Does the handle lever go thru the loop on the side flush valve tower before you connect the small chain? Answer: The gasket, or rubber ring, has deteriorated and needs to be replaced. Question: I changed the seal and now there are air bubbles coming in at the bottom. What should I try next? Answer: Although I'm not a plumber, just a DIY person, it sounds like the seal isn't in the right place.

Take out the rubber ring the seal and feel along the edge of the tower to find the ridges within which the seal is meant to be fitted. Then try re-inserting the rubber seal so that there's one set of ridges on either side of the seal.

The step by step instructions are like text-book for elementary kids, i followed it words by words, it worked like a charm that ended my month long struggle, thank you so much Sara for sharing this wonderful article with us! Thanks so much for these clear instructions! I was able to do this repair myself rather than waiting for my handy brother-in-law or spending money on a repairman. These instructions are exactly what I needed!

I suffered forever with the hard to flush handle and literally it took 4 minutes to replace and couldn't have been easier. ITEM UPC is Made by the Keeney Manufacturing Co.

One tip: The bottom of the tower may have some rubber gunk on it which transferred from the deteriorating seal, so take some toilet paper and clean off the gunk to ensure you get a nice tight seal. Oh, and if you have more than one Mansfield toilet, you might as well replace all of the seals at the same time while the process is fresh in your mind. All 3 of my toilets' seals were starting to go bad and make the toilet hard to flush.

Just tried this yesterday and I worked perfect, thank you for the clear instructions with pictures! Side bar: these are the bottom to the line in water closets.

I would suggest owners of these water closets have stoppage issues also. If you choose to replace, use an American Standard or Kohler elongated toilet. You will not be sorry. I've been lifting the lid for months to flush in fear of breaking the handle. Thank you so much. I know it had to be something simple but just wasn't sure. You and your pictures made it as easy as 1,2,3. Thanks again. The steps are so simple. You saved me a lot of time and money. Thanks again for your big heartedness!

Take out the tower as described. Not sure how long this lasts, but it fixed mine just now. If the seal is too tight, making the plastic slightly skinnier seems like an easier fix than a replacement. I used the red ones on two toilets, and it's been almost two years ago, and they're still working fine for me. One of them is for a guest bedroom bath, so that wouldn't make a good example since it's not used that much.

But the other is in the main bath and is used daily, and it's good, too. Anyway, that's been my experience, but the off brands may have more than one manufacturer. Maybe I just got a good one! Use only original Mansfield black seal. If you use an off brand or the red ones, it will leak again in 3 months.

I go to Ace Hardware and get the factory correct seals. Thank you so much for this! After breaking two flush levers from a very hard to flush toilet this seems to have fixed the problem. The pictures were a great help too! I had a similar problem and was pulling my hair out as I couldn't fix it. Mine was damaged in the same fashion as what that site depicted.

I followed the directions and bam - my toilet was repaired. It's always a bummer when you can't figure out why your toilet isn't flushing. We've been having that problem for a while now. Do you have any suggestions? This worked! Just replaced these on all of our Mansfield toilets and they are easy to flush again. Thanks for the article! Even after changing the guts they don't flush great. They have a flat spot after the trap.

Replace the toilet! Thank you for great Instructions.